Submitted by Apprehensive-Egg374 t3_10lfuwo in DIY
Maplelongjohn t1_j63xjib wrote
Reply to comment by Apprehensive-Egg374 in How can I add a second 1/4 inch water line to under my kitchen sink? by Apprehensive-Egg374
What I would do
Wait til Monday because an emergency plumber on the weekend cost 2x.
Shut off water
Drain system
Careful remove those valves. Unscrew the flex lines. Remove everything coming up from the old valves. Make sure to use 2 wrenches to counter hold the fixture so you don't accidentally snap anything off.
Remove the old valves holding the pipe coming out of the wall. Hopefully the threads stay on the pipe .
If that all comes apart without incident you've pretty much done it.
You need to verify the size of the pipe from the wall- is it 1/2 or 3/8" NPT (national pipe thread)
Find new quarter turn stops that fit that pipe(1/2 FPT(female pipe thread) x 3/8 compression is common)
You can find bullhead stops as well, so each fixture has a valve. 1/2 NPT x 3/8comp x 3/8 comp for dishwasher and likely one with a 3/8 & 1/4 comp for cold side.
https://www.lowes.com/pd/SharkBite-Brass-1-2-in-Fip-x-3-8-in-Compression-Quarter-Turn/1001852370
Now that would work to get you back to where you are now,. looking for a place to connect the fridge.
You can use a compression T https://www.lowes.com/pd/Dial-Brass-Evaporative-Cooler-Water-Hook-Up-Kit/3092871
But I'd use 1/4" copper tubing to connect that tee to the stop.
Then you'll have 2 @1/4 compression and one 3/8 compression fitting for sink, water filter and fridge.
The hot side you'll have 2 @ 3/8 for the faucet and the dishwasher
Apprehensive-Egg374 OP t1_j63yoy3 wrote
Thank you so so much!! That was very detailed and helpful!! I really appreciate it!
In case the pipe thread does come off, what would I do? I don’t have access to the other side of the pipe as it’s behind the wall…Would there be a way to fix it with an adaptor or something?
One more question if you don’t mind: Do you think it would be possible to setup a washing machine to get hot/cold water and drain to under the kitchen sink?
Maplelongjohn t1_j6456r2 wrote
Sometimes the pipe threads/ end of pipe can be removed with an easy out, if not that's where the plumber and a repipe comes into play.
Likely need to open the wall. What's on the other side of this wall?
Negative on that laundry.
But if you have a plumber come they can assess the situation and make recommendations.
Apprehensive-Egg374 OP t1_j6474tj wrote
The other side of the wall is another apartments bedroom. I live in an apartment building (I own my unit). Thats somewhat the issue. If the pipe threads come off, the other pipe thread is far behind the wall and I’d have the break the wall. And it’s possible the next pipe behind the wall also breaks off when you try take that pipe off lol so it can be endless. The building is very old and so I’m sure the piping is very old as well. Is there a way that if the threads come off, I could cut the pipe to make the ends straight, and then attach some type of adapter or something? Or the only way is really to keep removing pipes behind the wall till you get a thread?
Maplelongjohn t1_j64v3ap wrote
I imagine you can't even shut off your own unit without the whole building and thusly that assembly of stops and fittings you have there ...
I'd just add another add a t for the fridge and be done with it
Or get ready for a barely reasonable to quite large plumbers bill...
Chicago? I'd guess from the brass drain assembly.
Get an outlet cover on the electric, no reason for that.
Apprehensive-Egg374 OP t1_j651hln wrote
The super can close my apartments water. I’m in NY.
If the brass pipe coming from the wall brakes off, can I cut it and then deburr it, and then use this shark bite attachment?
Viewing a single comment thread. View all comments