Submitted by VanillianArt t3_z72d9s in DIY
SummitWanderer t1_iy4asq0 wrote
Yes, you can. But be very sure that it's actually empty, if you're not sure how to check - hire an electrician to check.
VanillianArt OP t1_iy4b2q1 wrote
also, do I just buy about a 30meter ethernet cable from amazon to run through the conduit or is there a special kind I need?
SummitWanderer t1_iy4bnzx wrote
In general, I don't run pre-terminated Ethernet. I find it far far easier to pull it and then terminate it myself. You can find spools of it on Amazon, and then you'd need to buy the proper tools to terminate (about $100-150 investment including a bigger spool). You can try buying a premade cable and pulling it with a fish tape and line, but depending on the size of the conduit you may get stuck.
paulstelian97 t1_iy4d4of wrote
Do make sure that you don't make your cable TOO long, especially if you care about fast links (10Gbps, though 1Gbps and 100Mbps can be affected too).
trashyratchet t1_iy4ehj6 wrote
It's pretty tough to make an ethernet run TOO long in a normal residential application. Even Cat5e max recommendation is 100 meters with about 5ns propagation loss per meter. Even in a very large home, 30m or so is about as long as you would typically see.
paulstelian97 t1_iy4en3n wrote
Yeah you probably need some sort of yard and connecting buildings for that to matter.
The max for 10Gbps is probably shorter.
trashyratchet t1_iy4f60r wrote
Its actually the same 100m recommendation, just with Cat6a.
EtherCJ t1_iy4dq2h wrote
Although when you are talking "too long" here you mean WAY too long. Like an extra unnecessary 40 feet. Having an extra 4 feet is no issue.
paulstelian97 t1_iy4dw64 wrote
A good quality cable can carry 1Gbps over some 80-100 meters. Splice it and you reduce the maximum significantly (as low as 20 meters before it slows down and maybe 40-50 meters before it fails completely)
Angdrambor t1_iy4f1ib wrote
I didn't even realize you could splice cat6
paulstelian97 t1_iy4fdec wrote
In my house everything is twisted pair (up to the GPON). I've seen some splicing done because we wouldn't redo the wiring, and it was fine (15 meters or so, 100Mbps). Now I have proper unspliced Gigabit links.
paulstelian97 t1_iy4gnds wrote
You can splice basically any cable. The splice WILL negatively affect the signal so it's a game of whether you can afford that
SummitWanderer t1_iy4ef91 wrote
Agreed, though I will say to date I've never had 1GbE impacted significantly by length and I've surpassed the max many times. Definitely depends on the existing environment.
SquirrelGod9000 t1_iy4g6qy wrote
And the quality of the cable as well.
paulstelian97 t1_iy4eitx wrote
If you prevent external interference in some other way you can break the rule I guess.
Tal_Star t1_iy4dfes wrote
You can but I would attempted to avoid using male ends as the little retaining clips tend to get broken. If both sides have a conduit box get female ends.
Go to your local computer shop they should be able to sell you bulk cable pretty cheap then grab female ends and face plates.
If you want to run it with the male end attached look at getting something like these guys. It will keep your install looking nice and clean.
https://www.amazon.ca/HuaHengHT-Ethernet-Network-Keystone-Coupler/dp/B099SGQWTP/
Angdrambor t1_iy4f6rw wrote
>male ends as the little retaining clips tend to get broken
If you have to pull a preterminated cable, it can be really helpful to tape those down.
cyberentomology t1_iy4m5cz wrote
And if it’s preterminated, you’re going to need a bigger conduit.
Sub_pup t1_iy4e7i1 wrote
Just dont exceed 100 meters.
Webic t1_iy4om0e wrote
Use plenum rated cable. Resists fire and doesn't release "as toxic" of fumes as regular cable.
StoviesAreYummy t1_iy4cu84 wrote
And at that point you'd be better off asking them to run it since you're paying for the time anyway
Viewing a single comment thread. View all comments