[removed]
Comments
yaaa4 OP t1_jdm0yhx wrote
The motor is ok. While disconnected it's sucks! Replacing pipe is a big job.. the house has been modified since the installation (the house is 60 years old). I'll probably buy a vacuum canister before replacing all the pipes...
M0U53YBE94 t1_jdjg9ij wrote
This is a sound thing. Make the house as quite as possible and start searching the areas where the pipes run. You will most likely have to get in the attic to hear the leak. It should be fairly obvious. Especially if your finding blown insulation inside the catch can.
yaaa4 OP t1_jdm17zp wrote
Good idea. However, the pipes are mainly in in the basement ceiling not in the attic. But worth a second try, I didn't stop my HVAC last time. I should try again
M0U53YBE94 t1_jdmf75o wrote
Bit easier to search then. Unless the ceilings are finished.
[deleted] t1_jdjeaa1 wrote
[deleted]
pirategirl50 t1_jdju95w wrote
This is an easy fix!! Get a shop vacuum and go to the garage-open the area where the debris goes into the bag. Stick the vacuum in there and turn it on. Have someone else check each opening as you do this. You will be shocked at what comes out!!
yaaa4 OP t1_jdm1goy wrote
I'll give it a try I guess...
dark-archon t1_jdjh47x wrote
Try running a flexible pipe through the existing ones and check the suction.
yaaa4 OP t1_jdm1kad wrote
You will have to explain me this one...
dark-archon t1_jdm3m9w wrote
Are the existing pipes hard PVC or flexible ? Sounds like you should replace the pipes anyway so if you can pull a smaller, flexible pipe through, you could check the suction on that one.
If it's still not good, the problem will be with the vacuum itself. If it's good, one pipe done.
[deleted] t1_jdjhoni wrote
[removed]
[deleted] t1_jdjs5ft wrote
[deleted]
Pravus_Belua t1_jdm71bn wrote
Your submission has been removed for one or more of the following reason(s):
- Your post was regarding cooking, cleaning, general maintenance items.
- Your post was regarding sewing, general automotive repairs, cosmetics.
- Your post was regarding software design, CNC, 3D or laser printing.
- Your post was otherwise not considered a good topic fit for this subreddit.
- Please consider submitting these projects to /r/crafts, /r/homeimprovement, /r/woodworking, /r/electronics or /r/findareddit to help you find a subreddit applicable to your project.
Please read our Full Sub Rules before resubmitting.
If you believe this was a mistake, please message the moderators.
###Do not respond to this comment - you will not receive a response.
jburcher11 t1_jdjqrdx wrote
What the heck is a central vacuum??
Reacti0n7 t1_jdjrxlm wrote
It's a system of pipes in your house that is attached to a vacuum motor. So all you do is walk around the house with a hose. Attach it to a port around the gouse and just hit an on button, instant vacuum.
jburcher11 t1_jdjs7cr wrote
TIL. Sounds fantastic.
Edit. Well if it worked, which I guess is OPs issue π
Reelplayer t1_jdjrpm5 wrote
Big vacuum and collection bin in a somewhat hidden location like a garage or utility room, pipes running through your attic and/ or walls to every room, and connection ports in every room to hook up a hose and often a floor tool. The idea is you can vacuum every room without lugging around a tank or upright vacuum, but in reality lugging around a 20' hose can be just as cumbersome.
jburcher11 t1_jdjsfxl wrote
Ty. You n the other guy. π
xjuslipjaditbshr t1_jdjek8o wrote
Probably best to try to isolate the problem. Can you for example test the motor independently by disconnecting it from the piping and and see if it has enough suction?
If the motor is good, then you know itβs the pipes. And if the pipes are old and crumbling, you probably need to replace them.