The other day my dryer (ds4500eb0ww) popped and smelled. I took it apart and see that the coil had broken. I ordered the whole coil unit and it was an easy replacement until I messed up. I left one wire undone and it is the main power to the coil.

As you can imagine it welded itself to the dryer housing. I replaced the spade connector and double checked my work a second time. All the wires are on. I can now start the dryer but there is no heat.

I checked the breaker and both breakers are on. The thermal fuse has continuity. Before I start throwing parts at, is there anywhere to start looking?

Comments

bb8c3por2d2 t1_jeatd38 wrote on March 30, 2023 at 5:45 PM

#2,493,108

Have you tried to reset the breakers? The drum will run with only 120v, but the heating element needs 220v.

steakhaus OP t1_jeau8kg wrote on March 30, 2023 at 5:50 PM

#2,493,313

Replying to bb8c3por2d2 (#2,493,108)

Thanks. Checked those. It’s an attached double breaker. I did flip them off and back on to double check. No dice.

Adam2013 t1_jeazdtg wrote on March 30, 2023 at 6:23 PM

#2,494,571

Replying to steakhaus (#2,493,313)

Check the control board for any blown glass fuses if you aren't getting 220VAC (in the US) between both spade connectors on the new coil

steakhaus OP t1_jebfznu wrote on March 30, 2023 at 8:09 PM

#2,498,640

Replying to Adam2013 (#2,494,571)

I don’t see any control boards. It’s a pretty old dryer. There looks to be a block where several wires connect on the side of the motor. It’s hard to get to are there fuses there possibly.

matt7718 t1_jebvckf wrote on March 30, 2023 at 9:47 PM

#2,502,387

Just a thought. Are you setting your dryer to a point in its cycle where it should be heating?

I was testing my gas dryer and thought i had fucked it up, but it turns out that my dryer just tumbles near the end of the cycle. Make sure you are setting it to a part of the cycle where it heats up when you are testing it.

Adam2013 t1_jecbcgl wrote on March 30, 2023 at 11:40 PM

#2,506,168

Replying to steakhaus (#2,498,640)

Try that, and make sure those connections are tight. Make sure the dryer is unplugged before you tighten

Do you have to a multimeter?

steakhaus OP t1_jed7t7s wrote on March 31, 2023 at 3:57 AM

#2,515,124

Replying to Adam2013 (#2,506,168)

I do have a multimeter. I checked the thermal fuse and it has continuity. I don’t know anything else to check. Those were the main search results.

steakhaus OP t1_jed7v1o wrote on March 31, 2023 at 3:58 AM

#2,515,143

Replying to matt7718 (#2,502,387)

I’ll double check but I’m pretty sure it was. Before it broke the setting it was on heated the old coil.

Adam2013 t1_jed88pk wrote on March 31, 2023 at 4:01 AM

#2,515,237

Replying to steakhaus (#2,515,124)

Check that the heating element has 240 volts across the inputs when the power is on. Be very careful when you're doing this, do not short anything and do not touch anything electrical with your body.

CanadianBaconMTL t1_jedcek1 wrote on March 31, 2023 at 4:43 AM

#2,516,398

Turn it on and check if that melted wire gets any voltage. Probably a blown fuse somewhere